Skip to main content

MV Transformers

 

  • Does HPS build secondary unit substation transformers?

      Secondary Unit Substation Transformers feed low voltage switchgear or switchboards. They typically range from 150 kVA to 2,500 kVA three-phase. The Primary voltage ranges from 2400 VAC to 34,500 VAC and the secondary from 600VAC to 480 VAC. Taps are typically manually changed while the unit is de-energized. The primary connections are typically delta connected while the secondaries are usually wye connected.

      The units are typically installed inside a building and are either dry (VPI) or cast coil because of safety and installation concerns. These units are often connected directly close coupled to the switchgear. HPS can provide both VPI and Cast Coil Secondary Unit Substation Transformers.

  • Does HPS build primary unit substation transformers?

      Primary Unit Substation Transformers are located outside and typically range from 750 kVA to 10,000 kVA three-phase. The Primary voltage ranges from 2400 VAC to over 100,000 VAC and the secondary from 2400 VAC to 34,500 VAC. Taps are typically manually changed while the unit is de-energized. The primary connections are typically delta using bushings, throats or air terminal chambers.

      While often oil, HPS dry-type transformers can offer similar performance with a lighter weight and fewer environmental concerns.

  • Does HPS build substation transformers?

      Substation transformers are located outside and typically range from 750 kVA to 5000 kVA single-phase and 25,000 kVA three-phase. The Primary voltage ranges from 2400 VAC to 46,000 and the secondary from 480 VAC to 15,000 VAC. Taps are typically manually changed while the unit is de-energized.

      While they are typically oil, HPS dry-type transformers can offer similar performance with a lighter weight and fewer environmental concerns.

  • What is the energy efficiency regulation compliance in the U.S. and Canada?

      In the past several years, there has been an accelerated rate of change in updating energy efficiency standards for transformers in North America.

      Governments in US and Canada are encouraging users to use higher energy efficiency dry-type transformers, to help reduce carbon dioxide emissions. There is also a long term cost savings in operating higher efficiency transformers translated in lower energy usage, lower cooling cost, etc.

      In U.S.A. the Department of Energy (DOE) has mandated new higher efficiency levels effective Jan. 1st 2016.

      In Canada Natural Resources Canada (NRCan) published SOR/2016-311 which amends the Energy Efficiency Act to align the via amendment 14 the minimum energy efficiency levels for dry type transformers to the ones implemented by DOE in Jan 2016.

      The new NRCan 2019 regulation is going to be enforced across Canada on May 1st, 2019. The Ontario government already adopted these new efficiency levels by publishing the ON Reg.404-12 which in schedule 6 defines the new energy efficiency levels that dry type transformers sold in ON must comply with starting Jan.1st 2018 (Ontario Energy Efficiency Compliance).

      The rest of Canada (including Quebec) is still following the current energy efficiency levels prescribed by CSA C802.2, until the new NRCan regulations come in effect on May 1st 2019.

      To help our valued customers in estimating the cost savings resulting from upgrading their old dry type transformer to the new DOE2016/NRCan2019 efficiency levels, HPS has developed an Energy Savings Calculator available on its website. To find out how HPS can help reduce your energy consumption, click here.

      To visit the Canadian Gazette for more information about the Canadian energy efficiency standards, click here.

      For the Ontario Energy efficiency regulation please click here.

      To view an electronic copy of the U.S. DOE energy efficient standards, click here.

  • What are the new Energy Efficiency levels coming for Transformers sold in the U.S.?

      Transformers have been and remain an essential part of our electrical infrastructure.  Everywhere we look there is a transformer supplying power to industrial, commercial or residential applications.

      In the past decades the greenhouse gas emissions and the effects on our planet have become the focus of many governments, agencies and individuals. Energy generation is a major contributor to the greenhouse gas emissions. In addition to widespread efforts to make energy generation more environmentally friendly, there is also a goal to lower energy consumption within most industrial, commercial and residential areas. Achieving increased energy efficiency levels for equipment and consumer products has become a priority for many manufacturers.

      Improving the energy efficiency of new transformers is a primary goal of the US Department of Energy (DOE), and they have the legal authority to define efficiency levels and enforce compliance.  Environmentally conscious consumers also recognize that buying a higher energy efficiency transformer will have a societal payback over many years.

      The Department of Energy has established new and more stringent Energy Efficiency levels for Transformers in the U.S. effective January 1st 2016.  The new efficiency levels for Medium Voltage Liquid-Filled, Medium Voltage and Low Voltage Dry-Type Distribution Transformers are defined in DOE’s CFR (Code of Federal Regulations) title 10 part 431.  Widely known as DOE 10 CFR p431, it was published in the Federal Register Vol. 78, No. 75 on Thursday April 18, 2013.  According to the DOE, the new efficiency levels are expected to reduce energy losses by an average of 18% in low-voltage dry-type distribution transformers and 13% for medium-voltage dry-type transformers, over the current TP-1 efficiency levels.

      To put the benefits of this change in perspective, the DOE projects savings up to $12.9 billion in total costs to consumers and 3.63 quadrillion Btu of energy over a 30 year period. In addition, about 265 million metric tons of carbon dioxide emissions will be avoided, equivalent to the annual greenhouse gas emissions of about 52 million automobiles.

      The subject of energy efficiency for transformers raises two main considerations:

      1. Under normal operation a transformer is always on (typically at 35% average loading), making any energy efficiency improvements more significant over an extended period of time.  This means that customers will be rewarded in two manners:  they are reducing greenhouse gas emissions and there is an economic payback through reduced energy costs.  Considering the life expectancy of a transformer and the fact that the transformer will be on 24 hours a day, 7 days a week for the next 25-30 years, even small energy efficiency improvements will pay dividends for decades.  A secondary benefit is that more efficient transformers generate less heat, and in many cases this translates into lower costs to cool the environment in which they are utilized.
      2. The currently mandated energy efficiency levels are already hovering around the 98-99% mark, depending on the type of transformer and ratings.  This means that any further efficiency improvements become more challenging to achieve, typically requiring more and/or better core and conductor materials.  This will directly impact the cost of the transformer in most cases.  However, as noted in point 1 above, there is an economic benefit to offset the higher initial transformer costs.  The new DOE 2016 compliant transformers that will come on the market will also be somewhat heavier than the current TP-1 efficiency level transformers.

      Hammond Power Solutions (HPS) has an online Energy Savings Calculator to help to our customers determine the savings they can achieve by installing a higher efficiency transformer.  It includes a comparison of transformers with older efficiencies to those of higher efficiency (TP1, NEMA Premium and DOE 2016 in the future) as well as specifics of the application and the customer’s cost of energy.

      Currently, for applications that require higher energy efficiency than the DOE regulated TP-1 levels, industry is using Premium Efficiency transformers defined by the NEMA Premium Efficiency Guidelines that stipulate approximately 30% lower loses than the TP-1 levels.  In terms of the environmental benefits of using a NEMA Premium transformer over a TP-1 rated let’s look at an example:

      The Electricity savings resulting from upgrading one three phase 75 kVA transformer can be translated into one of the following:

      • 1.19 Metric Tons of CO2
      • 121 Gallons of Gasoline
      • About 1/6th of the energy used by an average household annually
      • Planting 28 Trees
      • 0.9 Acres of Forest
      • Recycling 0.34 Metric Tons of Waste
      • Savings of $166 per year at $0.12 per kW-Hr

      Forest image 

      At some kVA ratings NEMA Premium energy efficiency levels meet or slightly exceed the DOE 2016 levels, some are slightly below the new requirements.  However, the NEMA Premium products are optional within the market today, and many consumers do not take advantage of the benefits they afford.  Hence, the DOE will require that all transformers manufactured after January 1st, 2016 will meet the new efficiency levels.

      The environmental impact and savings for our customers resulting from the DOE changes are positive and significant.  HPS fully embraces and supports this change, and the environmental benefits our society will receive as a result.  We proudly offer high quality transformers meeting the most stringent Energy efficiency requirements today and will be in a position to support the migration to the new DOE 2016 higher-efficiency designs for our valued partners and customers, beginning in the latter half of 2015.

  • New Energy Efficiency levels US 2016

      Transformers have been and remain an essential part of our electrical infrastructure.  Everywhere we look there is a transformer supplying power to industrial, commercial or residential applications.

      In the past decades the greenhouse gas emissions and the effects on our planet have become the focus of many governments, agencies and individuals. Energy generation is a major contributor to the greenhouse gas emissions. In addition to widespread efforts to make energy generation more environmentally friendly, there is also a goal to lower energy consumption within most industrial, commercial and residential areas. Achieving increased energy efficiency levels for equipment and consumer products has become a priority for many manufacturers.

      Improving the energy efficiency of new transformers is a primary goal of the US Department of Energy (DOE), and they have the legal authority to define efficiency levels and enforce compliance.  Environmentally conscious consumers also recognize that buying a higher energy efficiency transformer will have a societal payback over many years.

      The Department of Energy has established new and more stringent Energy Efficiency levels for Transformers in the U.S. effective January 1st 2016.  The new efficiency levels for Medium Voltage Liquid-Filled, Medium Voltage and Low Voltage Dry-Type Distribution Transformers are defined in DOE’s CFR (Code of Federal Regulations) title 10 part 431.  Widely known as DOE 10 CFR p431, it was published in the Federal Register Vol. 78, No. 75 on Thursday April 18, 2013.  According to the DOE, the new efficiency levels are expected to reduce energy losses by an average of 18% in low-voltage dry-type distribution transformers and 13% for medium-voltage dry-type transformers, over the current TP-1 efficiency levels.

      To put the benefits of this change in perspective, the DOE projects savings up to $12.9 billion in total costs to consumers and 3.63 quadrillion Btu of energy over a 30 year period. In addition, about 265 million metric tons of carbon dioxide emissions will be avoided, equivalent to the annual greenhouse gas emissions of about 52 million automobiles.

      The subject of energy efficiency for transformers raises two main considerations:

      (1) Under normal operation a transformer is always on (typically at 35% average loading), making any energy efficiency improvements more significant over an extended period of time.  This means that customers will be rewarded in two manners:  they are reducing greenhouse gas emissions and there is an economic payback through reduced energy costs.  Considering the life expectancy of a transformer and the fact that the transformer will be on 24 hours a day, 7 days a week for the next 25-30 years, even small energy efficiency improvements will pay dividends for decades.  A secondary benefit is that more efficient transformers generate less heat, and in many cases this translates into lower costs to cool the environment in which they are utilized.

      (2) The currently mandated energy efficiency levels are already hovering around the 98-99% mark, depending on the type of transformer and ratings.  This means that any further efficiency improvements become more challenging to achieve, typically requiring more and/or better core and conductor materials.  This will directly impact the cost of the transformer in most cases.  However, as noted in point 1 above, there is an economic benefit to offset the higher initial transformer costs.  The new DOE 2016 compliant transformers that will come on the market will also be somewhat heavier than the current TP-1 efficiency level transformers.

      Hammond Power Solutions (HPS) has an online Energy Savings Calculator to help to our customers determine the savings they can achieve by installing a higher efficiency transformer.  It includes a comparison of transformers with older efficiencies to those of higher efficiency (TP1, NEMA Premium and DOE 2016 in the future) as well as specifics of the application and the customer’s cost of energy.

      Currently, for applications that require higher energy efficiency than the DOE regulated TP-1 levels, industry is using Premium Efficiency transformers defined by the NEMA Premium Efficiency Guidelines that stipulate approximately 30% lower loses than the TP-1 levels.  In terms of the environmental benefits of using a NEMA Premium transformer over a TP-1 rated let’s look at an example:

      The Electricity savings resulting from upgrading one three phase 75 kVA transformer can be translated into one of the following:

      • 1.19 Metric Tons of CO2
      • 121 Gallons of Gasoline
      • About 1/6th of the energy used by an average household annually
      • Planting 28 Trees
      • 0.9 Acres of Forest
      • Recycling 0.34 Metric Tons of Waste
      • Savings of $166 per year at $0.12 per kW-Hr

      Dense Forest

       

      At some kVA ratings NEMA Premium energy efficiency levels meet or slightly exceed the DOE 2016 levels, some are slightly below the new requirements.  However, the NEMA Premium products are optional within the market today, and many consumers do not take advantage of the benefits they afford.  Hence, the DOE will require that all transformers manufactured after January 1st, 2016 will meet the new efficiency levels.

      The environmental impact and savings for our customers resulting from the DOE changes are positive and significant.  HPS fully embraces and supports this change, and the environmental benefits our society will receive as a result.  We proudly offer high quality transformers meeting the most stringent Energy efficiency requirements today and will be in a position to support the migration to the new DOE 2016 higher-efficiency designs for our valued partners and customers, beginning in the latter half of 2015.

  • What is ANSI NETA ATS-2017?
  • What is the base temperature rise of a transformer?

      The base temperature rise of a transformer is the maximum temperature rise at the expected full load capacity. Transformers can be built to run cooler than the base temperature rise, these are typically referred to as lower temperature rise transformers which can either operate in higher ambient temperatures or have additional service factor.

      • 105C Insulation System: 55C Base Temperature Rise
      • 150C Insulation System: 80C Base Temperature Rise
      • 180C Insulation System: 115C Base Temperature Rise
      • 220C Insulation System: 150C Base Temperature Rise

      The Hot Spot Allowance is added the expected ambient temperature and full load temperature rise to get the total expected temperature rise of a transformer.